The most common mistakes when building a roof
The roof, crowning the house, should be as reliable as all other constructions. However, errors in the construction of the roof are common enough. Therefore, the National Encyclopedia of Construction…

Continue reading →

How to choose without a mistake mineral wool for warming the house
Warming houses becomes of paramount importance, in the light of constantly rising tariffs for energy carriers. The national encyclopedia of construction, ProfiDom.com.ua, has already told you on what criteria you…

Continue reading →

As central heating developed and developed
The history of centralized heating (CO) has counted more than 100 years and throughout this time it is continuously evolving. The first water-based centralized heating distribution systems were put into…

Continue reading →

Wooden fence in the garden

Rain, wind, sun and snow – which just does not have to withstand the garden fence and have at the same time a decent look. Achieving this is not easy, but nothing is impossible, especially if equipped with high-quality equipment for finishing!
Wooden fence in the garden
So, the mission is to install a new fence in the garden. Garden fences look pretty pretty while protecting the fruits of the caring gardener – flowers, fruit and decorative trees, giving gardens and flower gardens a finished and spectacular look. And before each fence there is a special task – it should serve for a long time, look good and not be exposed to atmospheric factors as long as possible.

The final appearance of a wooden fence will depend on the aesthetic preferences of the owner. Nevertheless, in any case, for the manufacture of it we will need wooden or metal columns, which are installed and dug at a distance of 2-2.5 m from each other to a depth of at least 30 cm. For each column at the top and below screw the screws of beams. Between the columns, top and bottom, we put the crossbars and screw them on both sides using screws or nails. So, to the prepared basis, we nail shtahets, which can be purchased already ready or made by yourself from the cutting board.

As a result of mechanical processing in shchehetov or other elements of the fence small patches can be formed. In order to eliminate them, we use high-quality acrylic resin for VIDARON TM, which contains turpentine for very good adhesion of the impregnated mass with wood and specially prepared quartz flour, which provides a putty of the required strength and facilitates further treatment. Due to these substances, the putty layer does not crack during drying and it is easy to polish and polish.

An important point – the color of the putty must be selected in the form of wood, from which a fence is made, so that the sealed seats are invisible. Make it easy, because TM VIDARON offers twelve ready-to-use colors for this tool. So, no matter what kind of wood you would not decide to make a fence – alder, pine or oak – to find the appropriate putty to disguise the disadvantages, it is possible without problems.

Several tricks of applying putty will necessarily be useful: before applying the agent, carefully mix it, and inequalities and debris in the wood clean from dirt and dust. If the damage is deep, then you will have to apply several layers of putty, each time before applying another layer, waiting until the previous one dries. So, when the last layer dries, we polish the sealed places, clean the surface of the future fence from the dust and apply a layer of colorless protective and decorative imprenatum TM VIDARON, which will act as a primer and effectively protect the wood of the fence from biocorrosis.

After 24 hours after application of protective and decorative impregnate, we grind the elements of our fence with grinding paper, clean it from dust and proceed to apply the VIDARON PROTECTIVE-DECORATIVE VEGETABLES TM, which emphasizes the texture of the wood and forms a durable and elastic coating with a warranty of 6 years. LacoBeec can be used as transparent, and one of 14 colors.

The technology of applying the product is quite simple: before applying, lacquer thoroughly mix until a homogeneous consistency is obtained, so the brush evenly distribute the product on the surface of the fence and allow to dry. After 12 hours we perform interlayer grinding with abrasive paper of grainy 320 and apply another layer of lacquer. Again wait approximately 12 hours until it is completely dry, polish and apply the third, last, layer of lacobyceus. So many layers of the instrument are needed in order to achieve the best decorative effect and maximum performance of the covering of the fence, so our fence will admire the eye and the owner and his guests for a long time and no bad weather will not harm the fence thus framed.

Kitchen: creative area for cooking
The right and comfortable kitchen is a guarantee of a good and always uplifting mistress, and therefore - a delicious lunch and a healthy appetite. So that the process of…

...

How to insulate and unconstrain roofless roofs
There is a huge number of roof shapes and configurations for residential and public buildings. And quite often there are flat roofs, which, as well as ordinary rocks, need insulation…

...

Which primers and dry mixtures are used for thermal insulation of facades
In our country, 90 percent of the housing stock is physically and morally obsolete and is very worn out, and there is no opportunity to provide all who want affordable…

...

Fastening elements in the facade insulation system
Among the most common, types of thermal insulation of facades, which were described in one of our previous publications, the method of "wet facade" is considered to be most effective…

...